Japan's Fukushima nuclear plant begins fuel rod removal

This handout picture taken by Tokyo Electric Power Co (Tepco) on 14 November 2013 shows an operation using imitation fuel rods during an exercise to remove fuel rods from a pool at the unit four reactor building of Tepco's Fukushima Dai-ichi nuclear plant in the town of Okuma in Fukushima prefecture Tepco has been preparing for months to remove fuel rods at Fukushima

Related Stories

Workers at Japan's stricken Fukushima nuclear plant have begun removing fuel rods from a storage pond at the Unit 4 reactor building.

The delicate operation is seen as a necessary step in stabilising the site.

It will take about two days to remove the first 22 fuel rod assemblies, plant operator Tepco says.

Overall, more than 1,500 assemblies must be removed in what correspondents describe as a risky and dangerous operation set to take a year.

Experts say hydrogen explosions after the earthquake and tsunami in March 2011 have made the current storage facility vulnerable to further tremors.

The fuel rod assemblies are four-metre long tubes containing pellets of uranium fuel, and the fear is that some may have been damaged during the disaster.

Removing fuel rods

  • The fuel rods - 4m-long tubes containing pellets of uranium fuel - are in a precarious state in the Unit Four storage pool
  • The rod assemblies will be lifted out in batches of 22 in casks filled with water, using a crane - each batch will take 7-10 days
  • Two critical issues are whether the rods were damaged during the disaster and so are likely to leak, and whether the casks remain watertight so the rods have no contact with air
  • The fuel rods will be deposited into a new "common" pool with a cooling system

When the tsunami struck, water knocked out cooling systems to three of Fukushima's reactors, which went into a state of partial meltdown.

Unit 4 was undergoing maintenance, so all of its fuel rods were being stored. But a build-up of hydrogen triggered an explosion in Unit 4, damaging its structure.

'Important process'

The removal process, which has been preceded by months of repair work and planning, began on Monday afternoon.

"At 15:18 [06:18 GMT], we started to pull up the first fuel assembly with a crane," a spokesman for Tepco (Tokyo Electric Power Company) said.

A recently installed crane is being lowered into the pool and hooked on to the assemblies to place them inside a cask.

This handout picture taken by Tokyo Electric Power Co (Tepco) on 14 November  2013 shows an operation using imitation fuel rods during an exercise to remove the fuel rods from a pool at the unit four reactor building of Tepco's Fukushima Dai-ichi nuclear plant in the town of Okuma in Fukushima prefecture Removal of fuel rods from the storage pond is a key step in the decommissioning
This handout picture taken by Tokyo Electric Power Co (Tepco) on 13 November 2013 shows a cask of nuclear fuel being lifted and moved by Tepco workers during an exercise to remove fuel rods from a pool at the unit four reactor building of Tepco's Fukushima Dai-ichi nuclear plant in the town of Okuma in Fukushima prefecture Tepco has conducted trial runs of the process, which involves large casks

The fuel rods will then be deposited into a more secure storage pool with a cooling system.

Experts say it is vital that the casks are watertight so the rods have no contact with air - which risks overheating and possible contamination.

Yoshihide Suga, Japan's top government spokesman, said he hoped the operation would go as planned.

"We hope that this [process] will be conducted in a manner that will not disturb local residents, and that the removal will be done on schedule, properly and safely," he said.

Tepco spokesman Masayuki Ono called the operation "a very important process in moving ahead with the plant's decommissioning".

Nuclear Regulation Authority Chairman Shunichi Tanaka has warned that rubble from the blast in the pool could pose a problem, Kyodo news agency reported.

"The fuel has to be handled very carefully. There is a need to make sure that a fuel assembly is not pulled out (from the fuel rack) by force when it gets stuck because of the rubble," Kyodo news agency quoted him as saying.

The Fukushima nuclear power plant has suffered a number of setbacks in recent months, including a series of toxic water leaks and worker errors.

Graphic: Removing rods from reactor 4 at Fukushima
  • 1. Small crane retrieves spent fuel rods from storage pool. A protective shell has been built over the top of the damaged reactor building. There are 1,331 spent fuel rods and 202 unused fuel rods to be removed
  • 2. Fuel rods are carefully lowered into specially-constructed casks, which each weigh 91 tonnes and can hold up to 22 rods
  • 3. A larger crane lifts full cask out of the storage pond and lowers it out of the building and on to a flat-bed truck. The casks will then be taken to a safe storage pool on the Fukushima site

More on This Story

Related Stories

More Asia stories

RSS

Features & Analysis

Elsewhere on the BBC

  • StuntmanStuntman to the stars

    Driving dangerously and falling off buildings are all part of the day job for Bobby Holland Hanton

Programmes

  • A digger operated via an Oculus Rift and a controllerClick Watch

    Why controlling a heavy digger with a virtual reality helmet might improve safety

BBC © 2014 The BBC is not responsible for the content of external sites. Read more.

This page is best viewed in an up-to-date web browser with style sheets (CSS) enabled. While you will be able to view the content of this page in your current browser, you will not be able to get the full visual experience. Please consider upgrading your browser software or enabling style sheets (CSS) if you are able to do so.